03.14.2024 March Madness

My basket set pendants

Those of you who follow my Instagram account might remember that on Monday I put up this cute photo of my pendants, with the message that internet goblins ate the blog post I had all ready to go for March, 

My CR-V post impact

and THEN later that day I posted THIS photo of my car, after getting hit on the way home from running errands and stated there would be no blog post this month.

Today, after hours on the phone dealing with insurance, I changed my mind and decided I needed to write.

Originally, I had titled the post "A tisket, A tasket" because I was writing about making basket settings, and couldn't figure out how to tie that to basketBALL. I had considered "Slam Dunk" or "Nothing But Net" but those didn't work at all

Then Monday happened, and I decided that this week has, in fact, been madness...so that's the title I'm going to use...and now I will attempt to reconstruct my story about making basket settings for pendants.

I put a fair number of progress pictures up on my IG account, but I thought you might find a narration of the process interesting...so here goes.

An early - and still favorite
bezel set turquoise

I have set a lot of stones along my jewelry making journey, but they have all been bezel set - which means a piece of sheet metal was fitted tightly around a cabochon (flat backed stone) and soldered (or fused) to a backplate (another piece of sheet metal) to create the setting for the pendant.  

Bezel and basket settings use the same materials - sheet metal and wire (they can also be carved in wax and cast in metal) - to create the framework for the pendant, but that's pretty much where the similarity ends.

Beginnings of the basket

As with bezel setting, geometry and order of operations are critical for creating basket settings - maybe even more so.

For a basket setting you do shape the metal to match the shape of the stone - but these stones are faceted on the back - so instead of fitting inside the metal, the stone sits on top of the setting.

Instead of adding pieces to make the setting - as you do with a bezel pendant - you cut metal away to open up the basket.

I started with the turquoise because it's much easier to build a setting - any setting - for a round or oval stone than for one with corners like the tourmaline.

First set of prongs

After forming the sheet metal, and making sure the stone sits properly on top of it, you begin to cut away the center portion of the metal - leaving two thin bands.  

It's important that you only cut halfway around the setting at first, otherwise you will have two completely separate wire-thin pieces and completely eliminated the advantage of fabricating the basket from sheet.

Once the basket is half open, you attach the first set of prongs - which gives your piece stability while you open the other side - and then attach the other set of prongs.

Oops

The process is essentially the same for a square or rectangular stone, but there are corners - and those are tricky.  The base has to have 90 degree angles; to achieve those you create mitered corners by filing into the sheet metal before you bend it, and then you solder the corners to reinforce the metal.

If you file too deep - or get your metal too hot - your box will fall apart and you get to make it again...all part of the learning process.

Using 3rd arms to hold the piece in place

The second attempt at the rectangular setting went better, and faster, than the first...and turned out quite well.  Same process once I had the base constructed - cut out one side, solder carefully, cut out the other side, and finally attach a bail.

When making a pendant, you do need to leave a small piece of solid metal at the top of the basket so you have a place to anchor the bail.

A word about adding the bail.  That went much better on the second pendant as well - and had nothing to do with the shape of the basket.

Ready to polish and set

For the turquoise pendant, I got everything set up and attached the bail using pick soldering (picking up the solder with a special tool and placing it where it will flow and attach pieces together).  That works great, except when it doesn't, and because my solder didn't flow on the back side of the bail, I ended up melting it off and doing it twice.

For the tourmaline, I opted to sweat (melting the solder on to the frame before placing the bail down) solder the pieces together - learning from my mistake - and it went beautifully.

None of these setbacks were particularly frustrating or problematic - they were simply opportunities to learn - which is why I signed up for classes in the first place.  I went back to the bench with a desire not so much to make more of what I had done before, but to challenge myself to make new and different things.

Cookie - keeping me company

ACC is on spring break this week - but I'm excited to go back and fabricate another basket setting, or two, before the end of the semester. One of the truly wonderful things about being a continuing education student is that I can sign up for the same class more than once - so it's my intention to take Jewelry Technique 1 again, and continue to learn from master goldsmith Steve Kriechbaum.

Watch this space - there's definitely more to come!

Until next time.